9.6.6 build errors

[panagiotis m]

Hello Bill,

You do not need to disable error msgs to build a standalone. I am not sure
if you ever had to.

Kind regards,
Panos
--

On Tue, 1 Feb 2022 at 18:46, William Prothero via use-livecode <
use-livecode at lists.runrev.com> wrote:

> Regarding this, I don’t recall seeing a reply to my query about whether
> you still need to disable error messages when building a standalone.
> Hopefully this has been fixed, but …
>
> Best,
> Bill
>
> William A. Prothero, PhD
> Prof Emeritus, Dept of Earth Science
> University of California, Santa Barbara
>
> > On Feb 1, 2022, at 6:59 AM, matthias rebbe via use-livecode <
> use-livecode at lists.runrev.com> wrote:
> >
> > Mark,
> >
> > where are you saving the standalone to?
> > Any chance that the target folder is on iCloud drive. E.g. Desktop or
> Documents folder?
> >
> > I had similar problems in the past when i built the standalone directly
> on the Desktop or Documents folder which were both synchronized with iCloud
> Drive. I just cannot remember the correct error message. Sometimes the
> build process was successful and sometimes it was aborted.
> > I could solve this to select a target folder outside of iCloud Drive.
> > Btw. building the standalone in a Dropbox folder works w/o problems.
> >
> > Matthias
> >
> >> Am 01.02.2022 um 11:47 schrieb Mark Smith via use-livecode <
> use-livecode at lists.runrev.com>:
> >>
> >> Hi Panos,
> >>
> >> I did not change anything between attempts, just one right after the
> other. I guess I was observing this in RC2 and just persisted and it seemed
> to work on the 2nd or 3rd attempt. For good measure I just took the same
> stack and was able to build and install two more times without incident so
> it’s definitely not a repeatable problem and as yet I have no formula or
> hypothesis as to what might be causing it. I’ll keep an eye on it and log
> any similar problems I run across.
> >>
> >> Mark
> >>
> >>
> >>>> On Feb 1, 2022, at 10:23 AM, panagiotis m via use-livecode <
> use-livecode at lists.runrev.com> wrote:
> >>>
> >>> Hello Mark,
> >>>
> >>> I have not seen this before. Did anything change in your stack (used a
> >>> different provisioning profile or changed anything in the iOS
> settings) or
> >>> in the iOS device until the successful 3rd attempt?
> >>>
> >>> I cannot remember of anything that we changed in the 9.6.6 release
> cycle
> >>> that could have caused this behavior.
> >>>
> >>> Kind regards,
> >>> Panos
> >>>
> >>> On Tue, 1 Feb 2022 at 12:14, Mark Smith via use-livecode <
> >>> use-livecode at lists.runrev.com> wrote:
> >>>
> >>>> I just wanted to flag this issue. I am currently using the new release
> >>>> version of 9.6.6 although I did have similar problems with RC2 as
> well.
> >>>> This morning I took a stack I had previously built and successfully
> >>>> installed (using Development/Test Target -> iPhone) and tried
> installing
> >>>> it. The first time the app went through what appeared to be all the
> build
> >>>> steps but did not install the app. The 2nd time it went through all
> of the
> >>>> steps and then reported “Unknown Error” and the 3rd time it built and
> >>>> installed the app correctly. I’ve not noticed behaviour like this in
> >>>> previous versions. At the moment I have no hypothesis about what
> might be
> >>>> going on.
> >>>>
> >>>> Mark
> >>>>
> >>>>
> >>>> _______________________________________________
> >>>> use-livecode mailing list
> >>>> use-livecode at lists.runrev.com
> >>>> Please visit this url to subscribe, unsubscribe and manage your
> >>>> subscription preferences:
> >>>> http://lists.runrev.com/mailman/listinfo/use-livecode
> >>>>
> >>> _______________________________________________
> >>> use-livecode mailing list
> >>> use-livecode at lists.runrev.com
> >>> Please visit this url to subscribe, unsubscribe and manage your
> subscription preferences:
> >>> http://lists.runrev.com/mailman/listinfo/use-livecode
> >>
> >>
> >> _______________________________________________
> >> use-livecode mailing list
> >> use-livecode at lists.runrev.com
> >> Please visit this url to subscribe, unsubscribe and manage your
> subscription preferences:
> >> http://lists.runrev.com/mailman/listinfo/use-livecode
> >
> >
> > _______________________________________________
> > use-livecode mailing list
> > use-livecode at lists.runrev.com
> > Please visit this url to subscribe, unsubscribe and manage your
> subscription preferences:
> > http://lists.runrev.com/mailman/listinfo/use-livecode
>
>
> _______________________________________________
> use-livecode mailing list
> use-livecode at lists.runrev.com
> Please visit this url to subscribe, unsubscribe and manage your
> subscription preferences:
> http://lists.runrev.com/mailman/listinfo/use-livecode
>