9.6.6 build errors

[William Prothero]

Regarding this, I don’t recall seeing a reply to my query about whether you still need to disable error messages when building a standalone. Hopefully this has been fixed, but …

Best,
Bill

William A. Prothero, PhD
Prof Emeritus, Dept of Earth Science
University of California, Santa Barbara

> On Feb 1, 2022, at 6:59 AM, matthias rebbe via use-livecode <use-livecode at lists.runrev.com> wrote:
> 
> Mark,
> 
> where are you saving the standalone to?
> Any chance that the target folder is on iCloud drive. E.g. Desktop or Documents folder?
> 
> I had similar problems in the past when i built the standalone directly on the Desktop or Documents folder which were both synchronized with iCloud Drive. I just cannot remember the correct error message. Sometimes the build process was successful and sometimes it was aborted.
> I could solve this to select a target folder outside of iCloud Drive.
> Btw. building the standalone in a Dropbox folder works w/o problems.
> 
> Matthias
> 
>> Am 01.02.2022 um 11:47 schrieb Mark Smith via use-livecode <use-livecode at lists.runrev.com>:
>> 
>> Hi Panos,
>> 
>> I did not change anything between attempts, just one right after the other. I guess I was observing this in RC2 and just persisted and it seemed to work on the 2nd or 3rd attempt. For good measure I just took the same stack and was able to build and install two more times without incident so it’s definitely not a repeatable problem and as yet I have no formula or hypothesis as to what might be causing it. I’ll keep an eye on it and log any similar problems I run across. 
>> 
>> Mark
>> 
>> 
>>>> On Feb 1, 2022, at 10:23 AM, panagiotis m via use-livecode <use-livecode at lists.runrev.com> wrote:
>>> 
>>> Hello Mark,
>>> 
>>> I have not seen this before. Did anything change in your stack (used a
>>> different provisioning profile or changed anything in the iOS settings) or
>>> in the iOS device until the successful 3rd attempt?
>>> 
>>> I cannot remember of anything that we changed in the 9.6.6 release cycle
>>> that could have caused this behavior.
>>> 
>>> Kind regards,
>>> Panos
>>> 
>>> On Tue, 1 Feb 2022 at 12:14, Mark Smith via use-livecode <
>>> use-livecode at lists.runrev.com> wrote:
>>> 
>>>> I just wanted to flag this issue. I am currently using the new release
>>>> version of 9.6.6 although I did have similar problems with RC2 as well.
>>>> This morning I took a stack I had previously built and successfully
>>>> installed (using Development/Test Target -> iPhone) and tried installing
>>>> it. The first time the app went through what appeared to be all the build
>>>> steps but did not install the app. The 2nd time it went through all of the
>>>> steps and then reported “Unknown Error” and the 3rd time it built and
>>>> installed the app correctly. I’ve not noticed behaviour like this in
>>>> previous versions. At the moment I have no hypothesis about what might be
>>>> going on.
>>>> 
>>>> Mark
>>>> 
>>>> 
>>>> _______________________________________________
>>>> use-livecode mailing list
>>>> use-livecode at lists.runrev.com
>>>> Please visit this url to subscribe, unsubscribe and manage your
>>>> subscription preferences:
>>>> http://lists.runrev.com/mailman/listinfo/use-livecode
>>>> 
>>> _______________________________________________
>>> use-livecode mailing list
>>> use-livecode at lists.runrev.com
>>> Please visit this url to subscribe, unsubscribe and manage your subscription preferences:
>>> http://lists.runrev.com/mailman/listinfo/use-livecode
>> 
>> 
>> _______________________________________________
>> use-livecode mailing list
>> use-livecode at lists.runrev.com
>> Please visit this url to subscribe, unsubscribe and manage your subscription preferences:
>> http://lists.runrev.com/mailman/listinfo/use-livecode
> 
> 
> _______________________________________________
> use-livecode mailing list
> use-livecode at lists.runrev.com
> Please visit this url to subscribe, unsubscribe and manage your subscription preferences:
> http://lists.runrev.com/mailman/listinfo/use-livecode