How to divide card with/in 3 vertical lines?

Tore Nilsen tore.nilsen at me.com
Wed Oct 28 17:46:13 EDT 2020


You could of course also multiply the width of the card with 0.25, 0.5 and 0.75 to get the same results. Personally I prefer multiplication to division, but the results will be the same.

Best regards 
Tore Nilsen

> 28. okt. 2020 kl. 21:54 skrev William de Smet via use-livecode <use-livecode at lists.runrev.com>:
> 
> Thanks all,
> 
> The use of 1.3333 or (cardWidth/4)*3 did it!
> 
> 
> Greetings,
> 
> William
> 
> 
> 
> 
> Op wo 28 okt. 2020 om 21:28 schreef Brian Milby via use-livecode <
> use-livecode at lists.runrev.com>:
> 
>> Need to either use 1.3333 or for exact (in this case) (cardWidth/4)*3
>> 
>> Sent from my iPhone
>> 
>>> On Oct 28, 2020, at 4:16 PM, William de Smet via use-livecode <
>> use-livecode at lists.runrev.com> wrote:
>>> 
>>> Hi Scott,
>>> 
>>> Line 3 should be at loc 768,384 but is now at loc 770,384 (stack
>> 1024x768).
>>> This is because 'cardWidth/1.33' is not precise enough?
>>> 
>>> Greetings,
>>> 
>>> William
>>> 
>>> 
>>> 
>>> 
>>> Op wo 28 okt. 2020 om 20:54 schreef scott--- via use-livecode <
>>> use-livecode at lists.runrev.com>:
>>> 
>>>> When you say "almost perfect but not quite” what exactly are you
>> meaning?
>>>> 
>>>> —Scott
>>>> 
>>>>> On Oct 28, 2020, at 11:04 AM, William de Smet via use-livecode <
>>>> use-livecode at lists.runrev.com> wrote:
>>>>> 
>>>>> Hi there,
>>>>> 
>>>>> I need 3 vertical lines in my iOS app with equal distance and from top
>> to
>>>>> bottom.
>>>>> So I use the script below. It is almost perfect but not quite.
>>>>> Is there a better way to do this?
>>>>> ------
>>>>> *s*et the loc of grc "line1" to cardWidth/4, cardHeight/2
>>>>> set the loc of grc "line2" to cardWidth/2, cardHeight/2
>>>>> set the loc of grc "line3" to cardWidth/1.33, cardHeight/2
>>>>> 
>>>>> set the height of grc "line1" to cardHeight
>>>>> set the height of grc "line2" to cardHeight
>>>>> set the height of grc "line3" to cardHeight
>>>>> ------
>>>>> 
>>>>> greetings,
>>>>> 
>>>>> William
>>>>> _______________________________________________
>>>>> use-livecode mailing list
>>>>> use-livecode at lists.runrev.com
>>>>> Please visit this url to subscribe, unsubscribe and manage your
>>>> subscription preferences:
>>>>> http://lists.runrev.com/mailman/listinfo/use-livecode
>>>> 
>>>> 
>>>> _______________________________________________
>>>> use-livecode mailing list
>>>> use-livecode at lists.runrev.com
>>>> Please visit this url to subscribe, unsubscribe and manage your
>>>> subscription preferences:
>>>> http://lists.runrev.com/mailman/listinfo/use-livecode
>>>> 
>>> _______________________________________________
>>> use-livecode mailing list
>>> use-livecode at lists.runrev.com
>>> Please visit this url to subscribe, unsubscribe and manage your
>> subscription preferences:
>>> http://lists.runrev.com/mailman/listinfo/use-livecode
>> 
>> _______________________________________________
>> use-livecode mailing list
>> use-livecode at lists.runrev.com
>> Please visit this url to subscribe, unsubscribe and manage your
>> subscription preferences:
>> http://lists.runrev.com/mailman/listinfo/use-livecode
>> 
> _______________________________________________
> use-livecode mailing list
> use-livecode at lists.runrev.com
> Please visit this url to subscribe, unsubscribe and manage your subscription preferences:
> http://lists.runrev.com/mailman/listinfo/use-livecode





More information about the use-livecode mailing list