[ANN] animationEngine 2.9 available

[-= JB =-]

The stack is really cool too!   It is a definite must see.

thanks Chipp

-=>JB<=-


On Jun 21, 2008, at 9:35 AM, Randy Hengst wrote:

> JB,
>
> I have animationEngine 2.9 and have used Chipp's stack without  
> using 2.9. His stack works, but you need to click the Load Model  
> button.
>
> take care,
> randy
> ----
> On Jun 21, 2008, at 11:11 PM, -= JB =- wrote:
>
>> I thought the replacing of the substack and adding the new version
>> was supposed to proved the new link to put the stack in use.  And
>> below you will see some of the errors I get when I try to use the
>> stack.  This is after I have initialized animationEngine from the
>> message box and have checked to make sure it is in use.
>>
>> Here is part of an error and that is all I get are similar errors:
>>
>>
>>      	executing at 9:00:15 PM
>> Type	Chunk: no such object
>> Object	Main
>> Line	set the points of grc "xAxis" to tXPoints
>> Hint	xAxis
>>
>>
>> So the stack is in use but I cannot make Chipps stack work and
>> would really like to.  Any suggestions?
>>
>>
>> -=>JB<=-
>>
>>
>>
>> On Jun 21, 2008, at 8:18 AM, Björnke von Gierke wrote:
>>
>>> 1. animation engine is a stack like every other one. rev can't  
>>> magically find stacks on your hard disk. So it has to be open in  
>>> rev to be useful.
>>>
>>> 2. Animation Engine needs to be among the stacksInUse. to get it  
>>> there you need to execute this line of code: start using stack  
>>> "animationEngine"
>>>
>>> So what you need to do with Animation Engine and every other  
>>> library stack:
>>>
>>> 1. Open Animation Engine in rev
>>> 2. "start using stack "animationEngine""
>>> 3. open stacks that depend on the fact that Animation Engine is  
>>> being in use
>>>
>>> On 22 Jun 2008, at 03:50, -= JB =- wrote:
>>>
>>>> I deleted the substack, saved it and then from the message box  
>>>> while
>>>> Chipps stack was in front set the substack to animationEngine  
>>>> 2.9.  I
>>>> checked the substack list in Chipps stack and it is listed.
>>>>
>>>> But when I quit Rev and then doubleclick Chipps stack it opens then
>>>> gives me message it can't find the animationEngine library.  Should
>>>> I have put the animationEngine stack somewhere special.  I have it
>>>> located in the folder it came with and inside the main Rev  
>>>> folder with
>>>> Rev 2.9 and my other files.
>>>>
>>>> -=>JB<=-
>>>>
>>>>
>>>> On Jun 21, 2008, at 4:09 AM, Malte Brill wrote:
>>>>
>>>>> Hi JB,
>>>>>
>>>>> I was just checking chipps stack (which is way cool by the way!!!)
>>>>>
>>>>> The problem is that it carries an old version of AE as a  
>>>>> substack, so if you open chipps stack first then type into the  
>>>>> messagebox delete stack "animationEngine" then save chipps  
>>>>> stack and open the new version of ae and make that a substack  
>>>>> of chipps stack and save again, all should be fine.
>>>>>
>>>>> Hope that helps,
>>>>>
>>>>> Malte
>>>>>
>>>>> _______________________________________________
>>>>> use-revolution mailing list
>>>>> use-revolution at lists.runrev.com
>>>>> Please visit this url to subscribe, unsubscribe and manage your  
>>>>> subscription preferences:
>>>>> http://lists.runrev.com/mailman/listinfo/use-revolution
>>>>>
>>>>
>>>> _______________________________________________
>>>> use-revolution mailing list
>>>> use-revolution at lists.runrev.com
>>>> Please visit this url to subscribe, unsubscribe and manage your  
>>>> subscription preferences:
>>>> http://lists.runrev.com/mailman/listinfo/use-revolution
>>>
>>> _______________________________________________
>>> use-revolution mailing list
>>> use-revolution at lists.runrev.com
>>> Please visit this url to subscribe, unsubscribe and manage your  
>>> subscription preferences:
>>> http://lists.runrev.com/mailman/listinfo/use-revolution
>>>
>>
>> _______________________________________________
>> use-revolution mailing list
>> use-revolution at lists.runrev.com
>> Please visit this url to subscribe, unsubscribe and manage your  
>> subscription preferences:
>> http://lists.runrev.com/mailman/listinfo/use-revolution
>
> _______________________________________________
> use-revolution mailing list
> use-revolution at lists.runrev.com
> Please visit this url to subscribe, unsubscribe and manage your  
> subscription preferences:
> http://lists.runrev.com/mailman/listinfo/use-revolution
>